Valve installation guide and connection or welding method: Please be sure to remember the recommended valve is what is the use? And the application of environmental analysis, in order to determine the most suitable for the installation of what kind of valve. Before installing the correct valve, read the installation guide to prevent damage to the valve and to ensure that the valve is fully functional. Valve installation guide: 1, first along the vertical cutting pipe, and trim, remove burrs, measuring diameter. 2, the use of gauze or wire brush to clear the pipe and cutting parts, shiny metal surface shiny. It is recommended not to use steel wool. 3. Apply flux to the outside of the pipe and to the inside of the weld cover. The flux must completely cover the weld surface. Use solder sparingly. 4, to ensure that the valve is open. First pipe heating. As much heat is transferred from the pipe to the valve. Avoid prolonging the heating of the valve itself. 4a. Silver Brazing Method: Assemble the parts that need to be brazed. If the solder-coated parts are allowed to stand upright, the moisture in the solder evaporates and the dry solder easily peels off, exposing the exposed metal surfaces to oxidation. When connecting and assembling, insert the pipe into the pipe sleeve until it encounters blockage. Assembly is to ensure a solid support, so that the entire brazing operation can be maintained in a straight line position. Note: For valves of 1 inch or larger nominal diameter, it may be difficult to heat the connecting parts to the desired temperature at once. In order to maintain a normal temperature over a large area, two torches are usually required. It is advisable to preheat the entire jacket area appropriately. It is recommended to heat the connecting parts with acetylene flame. First, heat the pipe 1 inch above the valve and then flame the pipe alternately up and down around the pipe a short distance and rotate the pipe at an appropriate angle to avoid burning through the pipe. Flame to continuous movement, not allowed to stay at a certain point. In the valve sleeve base flame baking. Heating should be uniform, with a flame on the valve and pipe flame baking process should be extended to the valve on the flux no longer make a sound. Do not overheat the valve. As flux becomes liquid and semitransparent on the pipe and valve, the flame begins to advance and retreat along the axis of the connecting member to maintain the heat of the connecting member, particularly the valve sleeve base. 5, using the right amount of solder: If the use of linear solder, then the nominal diameter of 3/4 inch valve will be used 3/4 inch solder, and so on. If too much solder is used, some solder may flow through the pipe block and block the seal area. During the installation of the connecting parts, it can be seen that the solder and brazing alloy continue to flow. 5a. Silver Brazing Method: Place the wire or rod on the pipe socket in the valve. When the welding rod or wire into the junction to be removed from the flame above. When the alloy flows into the junction, move the flame back and forth. Once the proper temperature is reached, the alloy will quickly and easily flow into the space between the pipe housing and the valve sleeve. After the connection is full, you will see the edge of the solder alloy. 6, when the solder is in a sticky state, with a brush to remove excess solder clean. After the solder has cooled down, place a fillet around the port of the valve. Valves Imported pumps Industrial washers 1) Silver Brazing: The strength of brazed joints is not very good with different brazing materials depending on the normal, wide range of cleaning between the pipe shell and the valve sleeve maintenance work. The mechanical tolerances and surface smoothness of the internal diameter of silver-brazed valve bushings are very precise to ensure adequate adhesion. Note: Care should be taken to observe the residues of cleaning media during cleaning and removal. Brazing on surfaces that have been soiled or incorrectly cleaned is less than satisfactory because the silver brazing alloy does not flow or adhere to the oxide and the oily surfaces and exposed, Easily oxidized and lead to voids and debris repel solder. 2) Threaded connections: Dirt, dirt or any foreign material buildup in the pipe may interfere with the efficiency of the valve and seriously damage the valve's critical components. The interior of the pipe must be thoroughly cleaned with air or steam. When tapping the pipe, measure the size and length of the pipe threads and avoid clogging the pipe with the seat and disc. Thoroughly clean the thread end to remove any harmful steel or iron deposits. If you want to weld more solid, it is necessary to use Teflon tape or pipe adhesive. Only a small amount of pipe adhesive is used on the pipe threads, but pipe adhesives must not be used on the valve threads. Do not allow any pipe adhesive to flow into the valve body to avoid damage to the disc and seat. Before installation, cut off the fluid through the valve to make the valve work properly. Completely close the valve before installation. Place the wrench over the hexagonal head of the pipe to avoid any possible deformation. After installing the valve, to support the pipeline: the drooping pipe will cause the valve deformation and failure. 3) Flange connection: In order to ensure the correct installation of the valve flange, the following steps need to be followed. Carefully clean the joints first and then loosely attach two or three bolts to the base. Next, carefully insert the gasket into the connection. Bottom bolts help to position the washer and hold it in place. And then insert the bolt to be used to cross-tighten the way, do not use around tightening, which helps to eliminate the over-concentration of pressure). After normal use for a period of time, check that all bolts are tightened and re-tightened as necessary. This article Keywords: valve
Alligator Shear
What is the role of an Alligator Shear Machine in metal recycling?
The Alligator Shearing Machine which is commonly used in metal fabrication and scrap metal recycling to cut a range of metal items including pipes, bars, and even profile steel such as I-beams.
Each machine can be controlled manually or automatically.
The Alligator Shear Machine is easy to operate, safe and reliable, and can adapt to a variety of different environments.

How to choose a suitable Alligator Shear Machine?
Q43 series alligator shear is the ideal machine for shearing reinforcing bar, mild steel round bar, aluminium, copper, steel tubing, lead, cable and most other hard metals.
With the hold-down clamp device, to prevent material from kicking back and guarantee maximum operator safety, and do the shearing jobs most efficiently and safely.
We provide a variety of models of alligator shear, with various blades sizes for options, which support different working environments.
Q43-Alligator Shear (Integral structure design)
Q43-Alligator Shear (Split structure design)
YMSRECYCLING's wide range of Hydraulic Alligator Shear is designed for scrap yards and various industrial cutting applications.
These types of equipment can be customized and extended according to the actual needs of customers on-site.
YMSRECYCLING also offer economical and effective solutions to help you to process different scrap metal.
Please provide your requirements in consultation.
CONTACT YMSRECYCLING
Call us now on +86-15950122559
To start maximising your returns from your aluminum metal recycling.
Please email sales@ymsrecycling.com or visit our website directly for further information about the products you are interested in.
Scrap Metal Shearing Machine,Alligator Shear,Metal Cutting Machine,Hydraulic Alligator Shear,Alligator Shearing Machine
Jiangyin Yimaisheng Hydraulic Machinery Co., Ltd. , https://www.ymsrecycling.com