Curtis Tractor Sightseeing Cart Controller 1230-2402 200A 24V

Model NO.: 1230-2402
Application: E-Vechile and Series Motor Equipment
Brand Name: Curtis
Sizes: L164xw146xh56 mm
Throttle Type: 0-5K Ω
PWM Operating Frequency: 15 kHz
Trademark: Curtis
Origin: Anhui Hefei

Curtis Tractor Sightseeing Cart ControllerA 24V

Product Description
Curtis Tractor Sightseeing Cart ControllerA 24V

Overview

CURTIS Model: 1230-2402
Operating voltage range: 16 to 32 V
Nominal input voltage: 24 V
2 Minute Current Rating (amps): 200
1 Hour Current Rating (amps): 80
MOSFET overtemperature cutback: linear cutback starts at 100°C; complete cutoff at 110°C
MOSFET undertemperature cutback: approx. 50% motor current at -25°C; complete cutoff at -40°C
Throttle Type: 0-5K Ω (default setting), flexible throttle circuitry accommodates a variety of throttle types: 5kΩ-0, 0-5kΩ, 0-5V, etc.
Ambient Operating Temperature Range: -40°C to 50°C
Package environmental rating: IP53
Dimensions: L164xW146xH56 mm
Net Weight: 1.1 kg
Regulatory compliance:
EMC emissions: EN50081-2/08.93
EMC immunity: EN50082-2: 1995
Safety, uncontrolled runaway: EN1175
Features Include:

60-200 amp AC induction motor controller
MultiModeâ„¢ feature allows two distinct user-selectable operation modes
Easily programmable through the CURTIS Model 1313-4331 Handheld Programmer or 1314 PC Programming Station
Complete diagnostics through the programming devices and through the controller's built-in Status LED
Throttle input for single-ended or wigwag 5kΩ pots or 0-5V throttles (both standard full stroke and restricted range)
Active precharge of controller capacitor bank extends life of main contactor tips
Two hourmeters - total KSI-on hours and drive hours - and their associated maintenance timers are built into the controller, with EEPROM storage (no battery)
BDI calculations performed within controller
Meets EEC fault detection requirements
Fault detection circuitry on throttle inputs can be used to inhibit operation if throttle signal goes out of range for any reason (applies both to the traction throttle and, in applications that include a proportional valve, to the hydraulic throttle as well)
Stall protection
Internal reverse polarity protection (no external diode required)
Continuous diagnostics during operation, with microprocessor power-on self-test
All output drivers are short-circuit protected and provide built-in coil spike protection
Positive battery connections for all inputs
Fully protected inputs
Internal and external watchdog circuits ensure proper software operation
High environmental protection rating (IP53)
3-wire serial interface for multifunction display

Our Factory

Curtis Tractor Sightseeing Cart ControllerA 24V

Contact US
Curtis Tractor Sightseeing Cart ControllerA 24V

    The aluminum die casting part production flow chart

    Die casting production flow chart


    Commonly used materials of aluminum die casting: ADC12, ZL101, ZL102,A380, AlSi9Cu3, AlSi12(Fe);

    The precision of the aluminum die casting: ±0.1mm;

    Smoothness of surface of rough part: Ra1.6~Ra3.2;

    Shrinkage rate of aluminum die casting products: 0.5%;

    Material wastage rate: 5%;

    General aluminum die-casting machining allowance: 0.5mm~0.7mm;

    Surface preparation methods: Sand blasted, Shot blasting, Powder coating, Painting, Plating, Electrophoresis, Polishing


    The specific pressure parameters of aluminum die casting part

    Material

    Thickness of die casting parts≤3mm

    Thickness of Die Casting Parts>3mm

    Simple structure

    Complex structure

    Simple structure

    Complex structure

    Aluminum alloy

    25-35Mpa

    35-45Mpa

    45-60Mpa

    60-70Mpa

    Injection speed of die cast process

    Pouring liquid metal tie up chamber volume percent

    Injection speed(cm/s)

    ≤30

    30-60

    >60

    30-40

    20-30

    10-20

    High speed computing formula

    High speed computing formula


    V -------------Cavity volume (CM3);

    N ------------ Cavity No;

    D ------------ Die-casting drift (CM);

    T ------------- Proper filling time.

    Holding pressure time

    Material

    Thickness of die casting part<2.5mm

    Thickness of die-casting part>2.5~6mm

    Aluminum alloy

    1-2

    3-8


    Aluminum die casting mold temperature

    Aluminum die casting mold temperature

    Tm --------------- Aluminum Die Casting Mould required working temperature (℃);

    Th -------------- Aluminum Alloy pouring temperature (℃);

    △ t---------------The temperature control of tolerance (The general is 25℃).


    The Aluminum Alloy Die Casting production and QC control

    My company strength of aluminum die casting, CNC machining, and QA control


    Aluminum Die Casting Parts

    Aluminum Alloy Die Casting, Aluminum Pressure Die Casting, High Pressure Aluminum Die Casting, Aluminum Injection Die Casting

    NINGBO BEILUN LEMA MACHINERY TECHNOLOGY CO.,LTD , http://www.china-lema.com